Ventoy Forums › iVentoy General Use —— iVentoy 使用交流 › iVentoy Discussion Forum v
 Windows 11 - Cannot be installed with iVentoy

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Thread Modes
 Windows 11 - Cannot be installed with iVentoy
dimitrirodis Offline
Junior Member
**
Posts: 18
Threads: 12
Joined: May 2020
Reputation: 1
#1
06-27-2023, 02:33 AM
on iVentoy, Windows 11 will not install on my optiplex 3050. BIOS is set to AHCI. Windows will install fine with Ventoy on USB. When booted from iVentoy, the Windows setup prompts for drivers. If you press Shift-F10 while in windows setup and run DISKPART, I can see all of the disks.

Is there something I need to change?
Find
Reply
phil2sat Offline
Junior Member
**
Posts: 10
Threads: 2
Joined: Jun 2023
Reputation: 0
#2
06-29-2023, 05:25 PM
I had the same issue, for me it was a damaged iso.

Try redownloading actual windows11 with mediacreationtool

all unattend then you do with iventoy. tried to integrate but it wont load, if you go to image settings you can add a xml fle to each iso and also menu or autoboot
Find
Reply
dimitrirodis Offline
Junior Member
**
Posts: 18
Threads: 12
Joined: May 2020
Reputation: 1
#3
07-02-2023, 08:24 PM
I am using the same MSDN ISO from my USB stick that has Ventoy on it and it works fine, the ISO is not damaged.
Find
Reply
longpanda Offline
Administrator
*******
Posts: 1,358
Threads: 86
Joined: Apr 2020
Reputation: 133
#4
07-03-2023, 12:54 AM
What about the latest 1.0.07?
Find
Reply
dimitrirodis Offline
Junior Member
**
Posts: 18
Threads: 12
Joined: May 2020
Reputation: 1
#5
07-05-2023, 06:31 PM
No it does not work still, even with 1.0.08.

I tried uploading a picture, but the attachment was too large.

As I said before, if you boot to Windows 11 (MSDN June 2023, Consumer Releases), you immediately get a prompt to install drivers. If you press Shift-F10 and go to the command prompt, and type DISKPART and then LIST DISK, I can see my drives.
Find
Reply
longpanda Offline
Administrator
*******
Posts: 1,358
Threads: 86
Joined: Apr 2020
Reputation: 133
#6
07-06-2023, 12:42 AM
press Shift-F10 and go to the command prompt, then run
type X:\windows\system32\ventoy.log
type X:\windows\system32\ventoy\vtoype.log
Find
Reply
jofe Offline
Junior Member
**
Posts: 1
Threads: 0
Joined: Jul 2023
Reputation: 0
#7
07-10-2023, 09:13 AM (This post was last modified: 07-10-2023, 10:08 AM by jofe.)
(07-05-2023, 06:31 PM)dimitrirodis Wrote: No it does not work still, even with 1.0.08.

I tried uploading a picture, but the attachment was too large.

As I said before, if you boot to Windows 11 (MSDN June 2023, Consumer Releases), you immediately get a prompt to install drivers. If you press Shift-F10 and go to the command prompt, and type DISKPART and then LIST DISK, I can see my drives.
maybe the meaning of  "drivers"  is  the "driver software" rather than the "hard-disk drive"?
(07-06-2023, 12:42 AM)longpanda Wrote: press Shift-F10 and go to the command prompt, then run
type  X:\windows\system32\ventoy.log
type  X:\windows\system32\ventoy\vtoype.log
我也遇到了类似的问题，查看ventoy.log没有发现问题，可以正常访问http://x.x.x.x:16000/riso/id/3.iso
继续查看vtoype.log发现是httpdisk.exe 挂载iso镜像出错，提示如下：
HttpDisk：不能访问网络位置。有关网络排除故障的信息，请参阅Windows帮助。

手工运行以下命令：
cd x:\windows\system32\ventoy
httpdisk /mount 0 http://x.x.x.x:16000/riso/id/3.iso /cd Y:

没有出错提示，挂载成功。回到按照界面提示浏览并手工选择光盘Y:的对应目录后就可以正常安装了。
仔细检查过命令并没有出错，网络及服务器也正常，猜测可能是运行时服务还没准备好，加个延时也许能解决问题？
Find
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)