Hello! 
Dont work with external DHCP.

Config DHCP (Windows Server)


Result with load:


Log and Config iVentoy in Attachment

Attached Files

Thumbnail(s)
           

  log.txt (Size: 21.44 KB / Downloads: 1)

Hello,

i started using iVentoy few days ago.
I set internal server, transfered .iso file in iso folder, and then when i boot on PC that .iso file, screen is broken. I tried multiple resulutions via iVentoy 1.0.07 but same result.
In forum I cant find any article about that problem. Log file doesnt help either.

I tried Win10 and Win11 and get same result.

Do you have any tips for fixing this problem

First off, I would like to thank you for this project. I will soon buy the pro version to help support this project.

I am running 2 instances of pihole in a high avail. These are set up as dhcp servers and hand out static and dynamic leases. So iventoy is set to use external dhcp. In dnsmasq.conf I have the boot option for the "next-server":

dhcp-boot=iventoy_loader_16000,10.10.8.86,10.10.8.86

I get to boot from the pxe server just fine. But when I try to install from a Linux ISO like debian or ubuntu I get network problem. You can see from the images below that I get two "network cards" when I boot from the pxe server. One with the actual network card "ens160", and one called "wired connection 1". With the actual network card, it gets assigned with an ip address but not with dns, but if I switch to the "wired connection" it gets assigned with ip address and dns. With boot from pxe i auto assign the "ens160" network card on debian and ubuntu. 

Am I missing some crucial settings in my dnsmaq config file? Or is this a bug with iventoy running with external dhcp server? I am running iventoy-1.0.09 on debian but I also tried this on windows.

Attached Files

Thumbnail(s)
       

I would like to request the feature  in the iventoy server pings an IP address before assigning it to new client if the ip is (Active/busy) Iventoy Will Move To Ping Another Ip In The iventoy Dhcp Range . 

This would help prevent major issues with the DHCP server (Router Server Switch), as sometimes there are active IP addresses within the iventoy dhcp range, and the iventoy would mistakenly lease them again.
and this will cause Ip Conflict inside the network.


PS:
This feature is also commonly used in all Microsoft Windows servers to ensure there are no IP conflicts within the network.

Its possible to add the feature to boot VHDX or .VTOY Linux disk?

Hello,
Here is a Windows11 machine on which I want to start IVentoy. So I start iVentoy_64.exe after unpacking the downloaded zip file. Immediately afterwards, the iVentoy service starts without any problems. Then I select "exit" in the iVentoy menu, after which I try to restart iVentoy_64.exe, but unfortunately I always get the message "Starting . . .please wait . . . Service unavailable, the page will close!" Even after a restart of the Windows11 machine, the result persists unchanged, thei service cannot be started.
What can I do? I have tried to restart the iVentoy system since version 1.0.04 until 1.0.09 without success. The Defender or the firewall has been set to allow contact with the Internet, also without success.

So I need some help and support, thank you very much.

Translated with DeepL

[font=Söhne, ui-sans-serif, system-ui, -apple-system,]Its possible to add the feature to boot VHDX or .VTOY Linux disk?[/font]

Format kısmında disk bulunamadı hatası alıyorum farklı sistemler ile denedim durum değişmedi.

Attached Files

Thumbnail(s)
   

• 2023/07/09 --- 1.0.09 发布
  

1. Fix a bug when booting Windows 7 ISO file.
   
   
2. Fix a bug that get the incorrect subnet mask for virtual ip.
   
   
3. Bugfix, comments and suggestions are welcome.
   

Since finding out that the issue with the garbled screen was related to monitor resolution, I've tested this out on a few different computers. 1080p works on the few laptops I've tested, and also on a desktop monitor I have tried, but on another monitor I have that has 1366 x 768 I still get the garbled screen, but on this monitor it works if I select 1280x720. (In both Linux and Windows version of iVentoy if I try to select 1366x768 it says "Failed to update configuration: failed" )

If it is possible, it would be nice if in the boot menu, maybe under tools menu, there was a way to change the resolution so that if you run into the issue with the garbled screen you can change it from that menu rather than have to go back to iVentoy configuration page to change it, and then go back to the computer you are trying to boot.