It looks like it succeeded but with some warnings:
Copied the Windows ISO onto the USB flash drive and rebooted.
It did boot the USB and I can see the Ventoy menu.
I selected the Windows ISO menu item and it started the Setup.
But at install locations there was no USB location to choose.
I had run this Setup before from DVD with a blank USB flash drive inserted.
Inside the Setup it would list the USB but when you tried to select it as the target it would error and tell you USB installation not supported.
How is using Ventoy going to change that so I can install Windows to a USB flash drive?
Code:
[greno@renog13-lin01 ventoy-1.0.74]$ sudo ./Ventoy2Disk.sh -i /dev/sdc
[sudo] password for greno:
**********************************************
Ventoy: 1.0.74 x86_64
longpanda admin@ventoy.net
https://www.ventoy.net
**********************************************
Disk : /dev/sdc
Model: PNY USB 3.2.1 FD (scsi)
Size : 115 GB
Style: MBR
Attention:
You will install Ventoy to /dev/sdc.
All the data on the disk /dev/sdc will be lost!!!
Continue? (y/n) y
All the data on the disk /dev/sdc will be lost!!!
Double-check. Continue? (y/n) y
512+0 records in
512+0 records out
32768 bytes (33 kB) copied, 0.0189501 s, 1.7 MB/s
delete /dev/sdc1
Create partitions on /dev/sdc by parted in MBR style ...
Done
Wait for partitions ...
partition exist OK
create efi fat fs /dev/sdc2 ...
mkfs.vfat 3.0.12 (29 Oct 2011)
success
32+0 records in
32+0 records out
16384 bytes (16 kB) copied, 0.393813 s, 41.6 kB/s
Wait for partitions ...
/dev/sdc1 exist OK
/dev/sdc2 exist OK
partition exist OK
Format partition 1 /dev/sdc1 ...
mkexfatfs 1.3.0
Creating... done.
Flushing... done.
File system created successfully.
mkexfatfs success
writing data to disk ...
446+0 records in
446+0 records out
446 bytes (446 B) copied, 0.242498 s, 1.8 kB/s
dd: warning: partial read (320 bytes); suggest iflag=fullblock
1985+62 records in
1985+62 records out
1046177 bytes (1.0 MB) copied, 0.0664447 s, 15.7 MB/s
dd: warning: partial read (390 bytes); suggest iflag=fullblock
63748+1788 records in
63748+1788 records out
33311766 bytes (33 MB) copied, 2.77682 s, 12.0 MB/s
16+0 records in
16+0 records out
16 bytes (16 B) copied, 0.337267 s, 0.0 kB/s
4+0 records in
4+0 records out
4 bytes (4 B) copied, 0.00534649 s, 0.7 kB/s
sync data ...
esp partition processing ...
Open ventoy efi file 0x610ac0
ventoy x64 efi file size 1810432 ...
Open bootx64 efi file 0x610ac0
Open ventoy ia32 efi file 0x610f10
ventoy efi file size 1216512 ...
Open bootia32 efi file 0x610ac0
Install Ventoy to /dev/sdc successfully finished.Copied the Windows ISO onto the USB flash drive and rebooted.
It did boot the USB and I can see the Ventoy menu.
I selected the Windows ISO menu item and it started the Setup.
But at install locations there was no USB location to choose.
I had run this Setup before from DVD with a blank USB flash drive inserted.
Inside the Setup it would list the USB but when you tried to select it as the target it would error and tell you USB installation not supported.
How is using Ventoy going to change that so I can install Windows to a USB flash drive?