Thread Rating:
  • 2 Vote(s) - 4.5 Average
  • 1
  • 2
  • 3
  • 4
  • 5
WinPE10 8 Sergei Strelec x86_x64 2021.01.05 EN [Tested]
#21
Lenovo T 430 ,Lenovo ThinkPad X1 Carbon 7, HP 630 Ventoy 1.0.69 , WinPE10_8_Sergei_Strelec_x86_x64_2022.01.03_English, Legacy i UEFI ok.
Reply
#22
(02-17-2022, 02:14 PM)zeit Wrote: Lenovo T 430 ,Lenovo ThinkPad X1 Carbon 7, HP 630 Ventoy 1.0.69 , WinPE10_8_Sergei_Strelec_x86_x64_2022.01.03_English, Legacy i UEFI ok.
booting into winpe is ok but in uefi not all programs are displayed at startup
Reply
#23
Use Ventoy in CLI (Text-Based Mode) through the "Ventoy.Json" (Set "display_mode": "CLI")... it will fix most of your issues !!!!

For me it's the only fix !
Reply
#24
(02-18-2022, 11:29 PM)mamide Wrote: Use Ventoy in CLI (Text-Based Mode) through the "Ventoy.Json" (Set "display_mode": "CLI")... it will fix most of your issues !!!!

For me it's the only fix !
booting into winpe is ok but in uefi not all programs are displayed at startup whether (Set "display_mode": "CLI") in "Ventoy.Json"
Reply
#25
Strelec starts like this in the EFI regardless of whether you boot from Ventoy or as the Strelec manual states.
Reply
#26
WinPE10 8 Sergei Strelec x86_x64 2021.01.05 EN.iso with Ventoy 1.0.70 UEFI64 on Lenovo IdeaPad 300 works for me.
If I go to Explorer, I can see a 'DVD Drive ( J: ) USB_STRELEC' virtual drive which shows that the ISO has been mounted as drive J: and many program shortcuts point to programs on J:.
Reply
#27
(02-21-2022, 09:29 AM)Steve2926 Wrote: WinPE10 8 Sergei Strelec x86_x64 2021.01.05 EN.iso with Ventoy 1.0.70 UEFI64 on Lenovo IdeaPad 300 works for me.
If I go to Explorer, I can see a 'DVD Drive ( J: ) USB_STRELEC'  virtual drive which shows that the ISO has been mounted as drive J: and many program shortcuts point to programs on J:.
thanks Steve2926, because I test on ventoy.vhd, I get error ventoy does not mount iso file in uefi. When testing with ventoy usb, boot is always successful and mount iso file
Reply
#28
re:
WinPE10_8_S.Strelec_x86_x64_2021.iso
GandalfsWindows10PE_x64_2019.iso

on Ventoy-1.0.80, MBR boot

I hope I'm not repeating information - I didn't have time to read the whole thread.

I was able to run Gandalf and Sergei Strelecs ISO's after formatting the Ventoy partition to NTFS.
It had previously been exFAT, and neither would boot.
I used the "Normal" boot mode, instead of Winboot mode, strangely.
I had first tried all the other fixit recommendations.

Then . . .
After I installed Medicat, it messed things up to a certain extent.
Medicat booted and ran fine and . . .
Srelecs ISO booted fine, booting now in Winboot mode but . . .
Gandalf booted, but none of the programs would run, showing a "bad path" type of error.
Hiren Boot CD wouldn't boot no matter what I tried. 
Perhaps I can fix that by editing the Ventoy json file.
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)