02-17-2022, 02:14 PM
02-17-2022, 04:31 PM
(02-17-2022, 02:14 PM)zeit Wrote: [ -> ]Lenovo T 430 ,Lenovo ThinkPad X1 Carbon 7, HP 630 Ventoy 1.0.69 , WinPE10_8_Sergei_Strelec_x86_x64_2022.01.03_English, Legacy i UEFI ok.booting into winpe is ok but in uefi not all programs are displayed at startup
02-18-2022, 11:29 PM
Use Ventoy in CLI (Text-Based Mode) through the "Ventoy.Json" (Set "display_mode": "CLI")... it will fix most of your issues !!!!
For me it's the only fix !
For me it's the only fix !
02-20-2022, 04:49 PM
(02-18-2022, 11:29 PM)mamide Wrote: [ -> ]Use Ventoy in CLI (Text-Based Mode) through the "Ventoy.Json" (Set "display_mode": "CLI")... it will fix most of your issues !!!!booting into winpe is ok but in uefi not all programs are displayed at startup whether (Set "display_mode": "CLI") in "Ventoy.Json"
For me it's the only fix !
02-20-2022, 05:20 PM
Strelec starts like this in the EFI regardless of whether you boot from Ventoy or as the Strelec manual states.
02-21-2022, 09:29 AM
WinPE10 8 Sergei Strelec x86_x64 2021.01.05 EN.iso with Ventoy 1.0.70 UEFI64 on Lenovo IdeaPad 300 works for me.
If I go to Explorer, I can see a 'DVD Drive ( J: ) USB_STRELEC' virtual drive which shows that the ISO has been mounted as drive J: and many program shortcuts point to programs on J:.
If I go to Explorer, I can see a 'DVD Drive ( J: ) USB_STRELEC' virtual drive which shows that the ISO has been mounted as drive J: and many program shortcuts point to programs on J:.
02-21-2022, 12:30 PM
(02-21-2022, 09:29 AM)Steve2926 Wrote: [ -> ]WinPE10 8 Sergei Strelec x86_x64 2021.01.05 EN.iso with Ventoy 1.0.70 UEFI64 on Lenovo IdeaPad 300 works for me.thanks Steve2926, because I test on ventoy.vhd, I get error ventoy does not mount iso file in uefi. When testing with ventoy usb, boot is always successful and mount iso file
If I go to Explorer, I can see a 'DVD Drive ( J: ) USB_STRELEC' virtual drive which shows that the ISO has been mounted as drive J: and many program shortcuts point to programs on J:.
10-24-2022, 04:39 PM
re:
WinPE10_8_S.Strelec_x86_x64_2021.iso
GandalfsWindows10PE_x64_2019.iso
on Ventoy-1.0.80, MBR boot
I hope I'm not repeating information - I didn't have time to read the whole thread.
I was able to run Gandalf and Sergei Strelecs ISO's after formatting the Ventoy partition to NTFS.
It had previously been exFAT, and neither would boot.
I used the "Normal" boot mode, instead of Winboot mode, strangely.
I had first tried all the other fixit recommendations.
Then . . .
After I installed Medicat, it messed things up to a certain extent.
Medicat booted and ran fine and . . .
Srelecs ISO booted fine, booting now in Winboot mode but . . .
Gandalf booted, but none of the programs would run, showing a "bad path" type of error.
Hiren Boot CD wouldn't boot no matter what I tried.
Perhaps I can fix that by editing the Ventoy json file.
WinPE10_8_S.Strelec_x86_x64_2021.iso
GandalfsWindows10PE_x64_2019.iso
on Ventoy-1.0.80, MBR boot
I hope I'm not repeating information - I didn't have time to read the whole thread.
I was able to run Gandalf and Sergei Strelecs ISO's after formatting the Ventoy partition to NTFS.
It had previously been exFAT, and neither would boot.
I used the "Normal" boot mode, instead of Winboot mode, strangely.
I had first tried all the other fixit recommendations.
Then . . .
After I installed Medicat, it messed things up to a certain extent.
Medicat booted and ran fine and . . .
Srelecs ISO booted fine, booting now in Winboot mode but . . .
Gandalf booted, but none of the programs would run, showing a "bad path" type of error.
Hiren Boot CD wouldn't boot no matter what I tried.
Perhaps I can fix that by editing the Ventoy json file.